24/7 emergency locksmith across Dublin · 20–30 min response Call now: 087 437 7600

Our Latest Articles

Locksmith adjusting a uPVC door hinge

uPVC Door Alignment: How to Diagnose and Fix It

October 19, 2026

Most uPVC doors that catch on the threshold, leave an uneven gap or refuse to lock can be realigned in a few minutes with an Allen key. The trick is to work out which way the door has moved before you touch a screw. If the hinges are at their limit, or the frame, glazing or threshold is the real culprit, no amount of turning will hold, and that is the point to call a professional.

This guide walks you through the symptoms, the three hinge adjustments, the strike plate (keep) question, double doors, and the cases where we would stop you and say: this needs a tradesperson. It also covers a point many guides skip: if the door is an exit in a pub, restaurant or apartment block, alignment is a safety matter, not just a draught matter.

Ecslocksmiths
Get a Sticking uPVC Door Checked
If your door still catches or will not lock after adjustment, Ecslocksmiths provides lock repairs and installations for homes and businesses in Dublin.
Explore locksmith services

TL;DR

  • Diagnose first: a dragging door, an uneven side gap, a draught and a stiff key each need a different adjustment. Don’t turn every screw at once.
  • Flag hinges typically adjust in three ways: height, side to side, and compression towards the frame. Make small changes, then test.
  • If the door only locks when you lift it or force the handle, stop. Forcing can damage the multipoint mechanism.
  • A bowed leaf, an out-of-square frame, shifted glazing packers or worn hinges are not fixed by adjustment screws.
  • Fire exits and panic hardware in commercial premises need professional assessment and a maintenance record, not DIY tweaking.

Table of Contents

Why a uPVC door goes out of alignment

A uPVC door leaf is heavy. It carries a sealed glass unit or a solid panel, a multipoint lock and three or more hinges, and it swings thousands of times a year. Add seasonal expansion and contraction, and a leaf can drop by a few millimetres without anyone noticing, until it starts rubbing.

Manufacturers describe it the same way. One retailer’s help page notes that uPVC doors can drop or drift slightly with regular use and seasonal expansion, and that adjustable hinges exist so you can fine-tune height, lateral position and compression. That is the normal, harmless case, and it is the one you can fix yourself.

The less obvious cause is the opening itself. Installation guidance says the frame should be plumb, level and square, and recommends measuring both diagonals of the opening, treating a difference above 2 mm as out of square. That figure is one installation guide’s criterion, not a universal tolerance for every door system, but the principle holds: hinge screws are for fine-tuning, not for correcting a crooked frame.

Frame squareness checks versus hinge adjustments

Read the symptom before you pick up the Allen key

The most useful habit is to match what you see to the right adjustment. Turning everything at once removes your baseline and often creates new gaps.

What you notice Likely cause First adjustment to try
Door scrapes the threshold or catches on the floor Leaf has dropped Vertical (height) adjustment
Gap wider on the hinge side or latch side, uneven side gap Leaf sitting too far one way Lateral (side to side) adjustment
Hooks or latch miss the keeps, key stiff, handle needs lifting Leaf dropped or shifted sideways Height, then lateral, then check the keep
Draught or visible light around the seal, even though the door is square Seal not pressing evenly Compression adjustment
Contact at top and bottom but a gap in the middle Leaf may be bowed or warped Replacement of components, not adjustment
Door sags again within weeks Glazing packers, threshold support or frame Professional inspection

Before adjusting anything, check the simple things. Screwfix advises checking for loose hinge or handle screws first, because a loose fixing can mimic a dropped door. Tighten them, then close the door and see whether the problem has already improved.

What you need

The kit is modest:

  • An Allen (hex) key, usually 4 mm for flag hinge adjusters, though sizes vary by hinge, so check which fits snugly
  • A Phillips or flat-head screwdriver for covers and keeps
  • A spirit level
  • A pencil or masking tape to mark gap positions
  • A torch, so you can see the hinge ends and the lock points

If you can find the hinge manufacturer’s instructions, use them. Hinge designs differ: flag hinges generally give all three adjustments, while butt and T-hinges often give less movement.

Step by step: adjusting a uPVC door on flag hinges

  1. Open the door and look at the hinges. Remove any plastic covers (they clip off). Identify the adjusters: usually a screw in the end of the hinge for height, a screw in the side for lateral movement, and a second access point for compression.
  2. Mark your baseline. Close the door and note the gaps at the top, both sides and the bottom. A photo helps. Mark the position where the door rubs.
  3. Tighten loose fixings. Hinge screws into the frame, and the keep screws on the frame.
  4. Adjust height if the door drops. Insert the Allen key into the vertical adjuster at the bottom of the hinge (the top one on some designs) and turn it clockwise to raise the door, anticlockwise to lower it. Screwfix suggests starting with one or two full turns, then checking the result. Make the same change on each hinge if the door has three, so the leaf doesn’t twist.
  5. Adjust lateral movement for uneven side gaps. Turn the side adjusters in small increments, moving the leaf towards the wider gap. On a flag hinge, one guide describes opposing movements at top and bottom to create a squaring effect, which is useful if the leaf is leaning.
  6. Test after every change. Close the door without lifting the handle. Lock it. Open it. If the key turns freely and the handle lifts without resistance, you are close.
  7. Only then set compression. This presses the leaf more firmly against the seals. Do it evenly. Too much pressure makes the door harder to close and can damage the seals.

One manufacturer’s guide gives typical tolerances of about 4.5 mm vertically, 5 mm laterally and 2 mm for compression. These depend on the hinge model, so treat them as a sense of scale: you are working in millimetres, which is why small turns matter.

Strike plate and keep adjustment

When readers search for strike plate adjustment, the usual situation is a door that closes properly but won’t lock, or locks only when pulled hard. On a uPVC door the strike plates (keeps) sit on the frame and receive the hooks, rollers and latch of the multipoint lock.

Work through this order:

  • Fix the leaf position first. If the door has dropped, the lock points will miss their keeps however well the keeps are placed. Correct the door with hinge adjustment, then check the keeps.
  • Look at the wear marks. Close the door, lift the handle and see where each hook or roller meets its keep. A scuff mark above or below the opening shows the direction of the misalignment.
  • Move the keep only if the leaf is correct. Many uPVC keeps are adjustable with a small screw, or can be repositioned slightly. Move it a millimetre or so, retest, and repeat.
  • Don’t file or force. If the lock only works when you lift the door or push the handle hard, stop. The research is consistent: forcing the key or handle can damage the multipoint mechanism, and a jammed or damaged mechanism is more expensive than a visit.

If the lock still feels stiff after the door is square, the issue may be the lock itself rather than alignment. We cover that situation in our guide to double glazed door lock repair.

Stopping draughts without making things worse

A draught is the commonest reason people search for this topic, and the commonest mistake is to fit new seals first. A new seal won’t reliably cure a door that is twisted, dropped, warped or sitting in a distorted frame. Everest makes the same point in its trade guidance, so the sequence is:

  1. Correct the geometry so the door closes without lifting or forcing the handle.
  2. Check that the seal touches the frame all the way round. A strip of paper closed in the door should grip evenly at several points.
  3. Adjust compression only where the seal isn’t making contact.
  4. Replace the seal only if it is hard, cracked or flattened.

If the paper slips out easily at one corner, that corner needs more compression or the leaf needs lateral adjustment. If it slips out in the middle but grips at top and bottom, the leaf may be bowed, and no adjuster will fix that.

Aligning two uPVC doors (French and double doors)

With a pair of doors, the meeting edges, the central gap and the lock points all have to line up at once. The installation guidance identifies misalignment between the master and slave leaf as a reason the lock may fail to engage.

A safe approach:

  • Look at both leaves, not just the one that seems wrong. A gap at the top of the centre meeting edge on one side is often a tilted leaf, as in the reader question that keeps surfacing about a single leaf tilting.
  • Adjust the affected leaf laterally and in compression, in small steps.
  • After every change, check the central gap, the threshold clearance and the multipoint keeps on both leaves.
  • Don’t adjust one leaf in isolation. You will chase the problem round the pair.

The slave leaf is secured by shootbolts at top and bottom, and these must meet their keeps in the frame and threshold. If they don’t, the doors can still look closed while being insecure, which matters for insurance and for your own peace of mind.

When adjustment will not fix it

Hinge adjustment is fine-tuning. If the door keeps returning to the same fault, look further:

  • Out-of-square frame. Measure both diagonals of the opening. If they differ by more than a couple of millimetres, the frame or its fixings may need correction.
  • Threshold support. A threshold that isn’t properly supported can settle, taking the door with it.
  • Glazing packers. In a correctly installed door the glass is packed so it braces the leaf diagonally (toe-and-heeling). If the packers were omitted or have shifted, the leaf can sag repeatedly even after the hinges are adjusted. The sash needs repacking.
  • Worn or damaged hinges. If an adjuster spins without moving anything or the hinge body has cracked, replace the hinge.
  • Warped leaf. A door that touches at top and bottom but leaves a gap in the middle usually needs component replacement.
  • Worn multipoint keeps or gearbox. A door that is square but still stiff to lock needs the lock looked at.

These jobs are where a trained door technician earns the call-out. Repeated turning of adjustment screws on a door with a structural fault just uses up the remaining adjustment range.

Pubs, restaurants and managed buildings: alignment is a safety issue

A slightly draughty customer entrance is routine maintenance. An exit door that sticks, fails to close or needs a key to open is a different category.

Irish Building Regulations require adequate means of escape, and the principle is functional: escape routes must be safe and usable, not merely tidy. Dublin City Council’s fire safety register guidance says exit doors should be readily openable, and that panic bolts, crash bars and self-closing devices should be kept in fault-free condition.

For a pub, restaurant, office or the common areas of an apartment block, that means:

  • Judge a repair by reliable opening, closing, latching and escape, not by whether the gap looks even.
  • Test the whole assembly after any work: door, closer, latch and exit hardware.
  • Keep a record of faults and repairs.
  • Treat a sticking emergency exit, failed closer or misaligned panic bar as urgent and have it assessed professionally rather than adjusted like a domestic draught.

This is a general summary, not legal advice. Your fire safety obligations depend on the building and its use. If you are unsure what applies, ask your fire safety adviser or the relevant authority.

Our perspective: what we see on Dublin doors

We get calls where the first message is “my lock is broken” and the real problem turns out to be a door that has dropped three millimetres. That is good news for the caller, because the fix is cheaper than a new lock. It is also why we suggest checking alignment before you replace any hardware.

The pattern we see is that people turn the key harder, lift the handle harder and slam the door harder, and the multipoint mechanism pays for it. If you notice you have to do any of those things, stop and look at the door. A rubbing mark on the frame or an uneven gap will tell you more than the lock does.

Our perspective: what we see on Dublin doors — overview diagram

For homeowners, our advice is simple: try the small, reversible adjustments described above, make changes in tiny steps and photograph the starting point. If the door won’t hold its position, or the lock still binds when the door looks square, get someone to look at the frame, the packers and the lock together. Treating them as separate problems is how the same visit gets booked twice.

For pubs, restaurants and property managers, we would go further: don’t fix an exit door as a draught job. Make sure the closer, panic hardware and latch all work together, and keep a note of what was done and when.

— Barry

When to call a locksmith, and what we can do

Call someone if any of these apply:

  • The door locks only when lifted, or the key or handle needs force.
  • The door is stuck shut or you are locked out because of a jammed mechanism.
  • An adjuster spins freely or a hinge is damaged.
  • The door keeps dropping after adjustment.
  • The door is a fire exit or fitted with panic hardware.

We are ECS Locksmiths in Dublin, and our service covers residential, commercial and automotive work, including lock repair, rekeying, high-security lock installation and panic bars and emergency exit devices. We offer 24/7 availability and free estimates. If a misaligned door has left you locked out, our emergency lockout assistance is published at €85-€120, one-off. Other jobs, including door repair, are quoted individually, and we don’t publish a fixed price for them.

You can see everything we do on our services page, find local cover through our door repair pages for Dublin, or go to our Dublin locksmith page to get in touch.

A quick checklist before you start

  • Photograph the gaps and mark where the door rubs.
  • Tighten loose hinge, handle and keep screws.
  • Adjust one axis at a time, a turn or two at most.
  • Make the same change on every hinge when adjusting height.
  • Test the door open, closed and locked after every change.
  • Leave compression until last.
  • Stop if you must lift the handle or force the key.
  • If the fault returns, look at the frame, packers and threshold.

FAQ

How do you adjust a uPVC door?

Identify the symptom first, tighten any loose screws, then use an Allen key on the hinge adjusters: height for a door that drops, lateral for uneven gaps, compression for draughts. Turn in small increments, one or two turns at most, and test the door after each change. Hinge types vary, so check the manufacturer’s instructions where you can.

How much does it cost to adjust a uPVC door?

The cost depends on the fault, so there is no single figure. A simple hinge adjustment is a quick job, but a frame, packer or hinge problem takes longer and may need parts. At ECS Locksmiths we give free estimates, and we don’t publish a fixed price for door repair. Our emergency lockout assistance is €85-€120, one-off.

How do you stop draughts from a uPVC door?

Square the door first so it closes without lifting the handle, then check that the seal touches the frame evenly all the way round. Use compression adjustment only where contact is weak. Replacing the seal won’t help if the door is dropped, twisted or bowed.

How do you align two uPVC doors?

Check both leaves together. Adjust the affected leaf laterally and in compression so the meeting edges and lock points line up, and check the central gap, the threshold and the keeps after every change. If the shootbolts or multipoint hooks still miss their keeps, have the pair assessed.

Why won’t my uPVC door lock even though it closes?

Usually the leaf has dropped or shifted, so the hooks, rollers or latch miss their keeps. Correct the door position first, then look at the keep. If it still won’t lock without lifting the handle or forcing the key, stop and call a locksmith, because force can damage the multipoint mechanism.

Sources

upvc door alignmentadjust upvc doorstrike plate adjustmentrealign upvc doordoor alignment for locks
Back to Blog

What services do locksmiths in Ireland actually offer?

It’s more than just unlocking doors. Most locksmiths provide:

Emergency lockouts (home, car, business)

Lock repairs and replacements

Key cutting and rekeying

Security upgrades (e.g. anti-snap locks)

Car key replacement

How quickly can you respond to an emergency?

In emergency situations, typical arrival times should be at your location within 20-30 minutes. There are always professional locksmiths on standby, ready to handle any lockout or security emergency, ensuring safety is never compromised.

Can a lockmsith help with high-security locks and systems?

Absolutely! Most locksmiths specialise in advanced high-security lock systems, including electronic locks, biometric security, smart locks, and keyless entry systems. The should be trained in the latest security technologies, ensuring that they can provide the highest level of protection for your home, office, or vehicle. Ask for a free expert consultation to help you choose the right security system for your needs.

Will a locksmith provide a warranty on there services?

Yes, all locksmiths should stand by the quality of there work and offer a 100% satisfaction guarantee. Most would by default offer a warranty on all services, ensuring that you receive the best craftsmanship and long-lasting results.

Can a locksmith open Cars

Yes, most locksmiths are trained to open cars.

How quickly can a locksmith get to me in an emergency?

Most locksmiths in Ireland offer 24/7 emergency callouts and typically arrive within 15–60 minutes, depending on your location and traffic. In Dublin, response times can be as fast as 10–30 minutes, especially for emergency lockouts.

Can a locksmith open my door without damaging it?

Yes A professional locksmiths use non-destructive entry methods first. Drilling is usually a last resort, not the default approach.

If someone immediately suggests drilling without inspecting the lock, that’s a red flag.

How much does a locksmith cost?

Costs vary depending on the service, time of day, and complexity of the job. A standard lockout is usually cheaper than replacing a lock. Emergency or late-night services may cost more.

Prices vary, but here’s a realistic guide:

Standard callout/labour: €85–€95

Lockout service: from ~€85–€120+

Lock replacement: depends on parts + labour

Important: Always ask for a full quote upfront and if there is a call out fee. Some companies advertise low prices but increase costs after arriving.

Prices can vary quite a bit… call around for quotes!

Can you make a key without the original?

Yes A professional locksmiths use non-destructive methods whenever possible. Damage usually only happens if the lock is faulty, high-security, or has already been tampered with.

Do locksmiths in Ireland need to be licensed?

Yes. In Ireland, all locksmiths must be licensed by the Private Security Authority (PSA).

If you’re hiring someone:

Ask for their PSA licence number

Avoid anyone who can’t prove credentials

By asking for the licence you avoid the scammers.

Providing Locksmith Services For More Than 30 Years in Dublin, lock outs, lock fitting, slam locks, car opening, commerical and domestic.

Quick Links

Home

About Us

Services

Testimonial

Faqs

Contact Us

All Dublin Areas

Malahide

00353874377600

Legal

Privacy Policy

Terms & Conditions